[Invazen]

I'm looking to replace my wide rear axle with a stock. Anyone know how much it'd cost and does anyone got a service manual download for free to do so? Was gonna try to do it myself. Also, a manual on to replace bearings beside the chain sproket because I think mine are bad, I can grab the handle bars and go up and down with it and it wobbles really bad. Pretty sure it's the bearings. Rides fine though, no crunching sounds etc.


Here is a picture of it. I hate it.

 

[Billy250X]

Thats a g force +7.5 axle.I have one to.There nice axles.It's easy to switch out axles.Just remember how it all came apart.But for bearings just buy a new carrier.It's less headache.

 

[300ex power by monster]

what type of quad is that

 

[TRX2fiveO]

is that a 300ex? How much for the Axle? you going back stock right? Welcome to the forums

 

[Billy250X]

300ex.I figured you of all people would know that.

 

[mud99]

They are simple to change. Why do you want to get rid of that one?

 

[Invazen]

I don't know if it's a g force 7.5 or not. It was on it when I got it. I'd like to trade it to a stock, I don't like the way it turns with it. Look's funny as well because they sit out so much farther than the front.

 

[Billy250X]

I'm pretty certain it's a g force.I think moose wants to trade you.

 

[300ex power by monster]

i got a stock 300ex rear end i willing to trad u

 

[Invazen]

i got a stock 300ex rear end i willing to trad u

Well, you're not local. Really would hate to yank it apart not knowing what I'm doing and shit it out. Lol

 

[TRX2fiveO]

flip your front wheels around and see how much better it looks. but make sure you have short valvestems your calipers will rip them out.

 

[TRX2fiveO]

Where are you located?

 

[Invazen]

Richmond, Ky

22x10x9 Rear
23x7x10 Front

if I remember correctly^^ That would look extremely funny lol. I'd never get any traction because my front tires are COMPLETELY bald in the middle. Not got around to getting any new ones yet.

My quad looks like shit because the plastic but it doesn't bother me. Runs fine and starts first time even in this cold weather below freezing temps. I got it for $800 so I guess it's worth it. Clutch and everything works extremely well. Just needs back brake pads and maybe a bearing casing for the back end. Honda ATV here said they'd fix it for $140 for the bearings + back brakes. Just not got a truck atm to take it up there. It blew up, haha

 

[TRX2fiveO]

actually it dosen't look any different just wider my fronts were flipped for a long time you really need to replace the dune slicks...lol

 

[Invazen]

actually it dosen't look any different just wider my fronts were flipped for a long time you really need to replace the dune slicks...lol

Dune Slicks, lol. Those are actually ITPs worn down really bad. I let some air out of them and I get pretty good traction from the tread on the sides. I'm gonna buy a whole new set of tires once I can get my bearings fixed and back brake pads. Want to do it myself, but can't find a manual without paying. Have no way to buy them online at the moment.

 

[TRX2fiveO]

my 250X manual is the same as far as the rearend goes I can scan the pages for you tomorrow and send them to you just pm me your email. oh wait I got a 300ex manual on here send me your email and I will try to send it to you.

 

[Invazen]

my 250X manual is the same as far as the rearend goes I can scan the pages for you tomorrow and send them to you just pm me your email. oh wait I got a 300ex manual on here send me your email and I will try to send it to you.

THANK YOU!

[email protected]

 

[TRX2fiveO]

be there shortly buddy enjoy and dont stay up too late reading...lol if you don't see it tonight it will be there tomorrow morning

 

[Invazen]

Thank you so much!!

I'm about to lay down, will check to see if I got it in the morning.

 

[TRX2fiveO]

Check now You should have it. just let me know about the axle gimme a figure